Stairs: common sizes at a glance
Worked out with the calculator above, including its default waste allowance. Your own numbers go in the calculator.
| Project | Risers (steps up) | What to buy |
|---|---|---|
| 24 in | 4 steps | 4 boards (2x12) · 6 boards (5.5 in) |
| 36 in | 5 steps | 4 boards (2x12) · 8 boards (5.5 in) |
| 48 in | 7 steps | 4 boards (2x12) · 12 boards (5.5 in) |
| 60 in | 8 steps | 4 boards (2x12) · 14 boards (5.5 in) |
| 96 in | 13 steps | 4 boards (2x12) · 24 boards (5.5 in) |
How to calculate stairs
- Risers: divide the total rise by the highest riser you allow and round up.
- Riser height: divide the total rise by the number of risers, so every step is the same.
- Treads: one less than the risers, because the deck or floor is the top step.
- Total run: treads × tread depth.
- Stringer length: the diagonal, √(rise² + run²).
A deck 36 in above the ground: 36 ÷ 7.75 = 4.6, so 5 risers of 7.2 in (just over 7 3/16 in). Four treads of 10 in make a 40 in run, the stringer is √(36² + 40²) = 53.8 in long and the stair climbs at 35.8 degrees.
| Total rise | Risers | Riser height | Treads | Run | Stringer |
|---|---|---|---|---|---|
| 18 in | 3 | 6 in | 2 | 20 in | 26.9 in |
| 24 in | 4 | 6 in | 3 | 30 in | 38.4 in |
| 30 in | 4 | 7.5 in | 3 | 30 in | 42.4 in |
| 36 in | 5 | 7.2 in | 4 | 40 in | 53.8 in |
| 48 in | 7 | 6.86 in | 6 | 60 in | 76.8 in |
| 60 in | 8 | 7.5 in | 7 | 70 in | 92.2 in |
| 72 in | 10 | 7.2 in | 9 | 90 in | 115.3 in |
| 96 in | 13 | 7.38 in | 12 | 120 in | 153.7 in |
The table uses a 7 3/4 in maximum riser and 10 in treads. In metric, a 90 cm rise with 19 cm risers gives 5 risers of 18 cm, 4 treads of 28 cm and a 112 cm run.
Stringers and treads
- Stringers: cut from 2x12 lumber, spaced no more than 16 in (40 cm) apart. A 36 in stair takes 4, a 60 in stair 5. Some composite tread makers ask for 12 in: check the install guide.
- Stringer stock: buy boards longer than the stringer length. 2x12s are usually sold from 8 ft in 2 ft steps.
- Treads: boards cut to the stair width. Two 5.5 in boards with a small gap make an 11 in tread; one 2x12 makes a single tread.
Measure the rise where the bottom step will actually land, not at the house. On sloped ground the rise changes, and the IRC allows only 3/8 in of difference between the tallest and the shortest riser in a flight.
Code limits at a glance
| Rule (IRC, US homes) | Limit | Metric |
|---|---|---|
| Riser height | 7 3/4 in max | 19.7 cm |
| Tread depth | 10 in min | 25.4 cm |
| Stair width | 36 in min | 91 cm |
| Headroom | 6 ft 8 in min | 2.03 m |
| Rise between landings | 12 ft 7 in max | 3.84 m |
| Handrail | 4 or more risers, 34 to 38 in high | 86 to 97 cm |
Other countries use similar limits. A common comfort check anywhere: two risers plus one tread should add up to about 24 to 25 in (61 to 64 cm).
Questions people ask
How many steps do I need for a 3 ft rise?
Five risers of 7.2 in and four treads, because the deck itself is the top step. With 10 in treads the stair runs 40 in out from the deck.
How long is a stair stringer?
The diagonal of the rise and the run: √(rise² + run²). For a 36 in rise and a 40 in run that is 53.8 in, so an 8 ft 2x12 makes one stringer.
How many stringers do I need?
Enough to keep them no more than 16 in apart: 4 for a 36 in or 48 in wide stair, 5 for 60 in. Composite treads often need them 12 in apart.
What is a good stair angle?
Between 30 and 37 degrees. Risers of 7 in with 11 in treads give 32.5 degrees, an easy outdoor stair. The IRC maximum riser on a minimum tread is close to 38 degrees.
Sources and data
- International Residential Code 2021, Section R311.7 (stairways)
- Comfort rule for stairs: two risers plus one tread of about 24 to 25 in (61 to 64 cm)
Last reviewed November 16, 2026 · How we calculate