Skip to content
Measured Yard

Asphalt Calculator

Enter the area and the compacted thickness. You get the tons of hot mix to order, the volume and the area, with a little extra for edges and low spots.

Your project

ft
ft

Driveways: 2 to 3 in once rolled, over a compacted gravel base. Overlays: 1.5 to 2 in.

in
Fine tune

5% covers edges, low spots and what stays in the truck bed.

%
Prices (optional)Type your local prices to see what it costs.
$

You need

9.13tons

Asphalt needed

Volume
4.67 cu yd
Area
480 sq ft

Shopping list

  • Hot mix asphalt9.5 tons

Counts are rounded up so you are never short. Weights are typical. Your supplier's may differ by about 10%.

Asphalt: common sizes at a glance

Worked out with the calculator above, including its default waste allowance. Your own numbers go in the calculator.

ProjectAsphalt neededWhat to buy
10 × 20 ft · 3 in3.81 tons4 tons
12 × 24 ft · 3 in5.48 tons5.5 tons
12 × 50 ft · 3 in11.42 tons11.5 tons
20 × 40 ft · 3 in15.22 tons15.5 tons
24 × 24 ft · 2 in7.31 tons7.5 tons

How much asphalt do I need?

Multiply the area by the compacted thickness to get the volume, then by the weight of compacted hot mix: about 145 lb per cubic foot (2,320 kg per m³). Divide by 2,000 for tons.

A 12 × 40 ft driveway at 3 in is 120 cubic feet. With 5% extra that is 126 cubic feet, or 18,270 lb: 9.1 tons, ordered as 9.5.

Compacted thicknessOne ton coversOne tonne covers
1.5 in (4 cm)110 sq ft10.8 m²
2 in (5 cm)83 sq ft8.6 m²
3 in (7.5 cm)55 sq ft5.7 m²
4 in (10 cm)41 sq ft4.3 m²

The layers of an asphalt driveway

  • Gravel base: 4 to 8 in (10 to 20 cm) of compacted crushed stone, deeper on clay or soft ground. Use the gravel calculator with crusher run for this layer.
  • Hot mix: 2 to 3 in (5 to 7.5 cm) after rolling for cars, 3 to 4 in for heavier trucks. It is often laid in two lifts.
  • Overlay: 1.5 to 2 in (4 to 5 cm) over sound old asphalt.

Enter the thickness after rolling. Hot mix is spread roughly a quarter thicker and rolled down, but it is ordered by its compacted weight.

Tons versus cubic yards

A cubic yard of compacted hot mix weighs about 3,900 lb, close to 2 tons. Paving crews use the same figure as 110 lb per square yard per inch of thickness. Plants sell by the ton, often with a small load fee under a few tons, so round up rather than down.

Questions people ask

How much area does a ton of asphalt cover?

About 83 square feet at 2 inches compacted, 55 at 3 inches and 41 at 4 inches.

How many tons of asphalt for a 20 × 20 driveway?

At 3 in compacted, 7.25 tons, or 7.6 with 5% extra: order 8 tons.

How much does a cubic yard of asphalt weigh?

About 3,900 lb once compacted, close to 2 tons (about 2,320 kg per m³).

How thick should an asphalt driveway be?

2 to 3 in of hot mix after rolling, over 4 to 8 in of compacted gravel base. Driveways that carry trucks or RVs need 3 to 4 in.

Sources and data

  • Hot mix asphalt weight: about 145 lb per cu ft compacted, the basis of the paving rule of 110 lb per square yard per inch
  • Asphalt paving industry guidance on residential driveway layers

Last reviewed November 16, 2026 · How we calculate

Next steps in your project