Skip to content
Measured Yard

Roofing Calculator

Measure the house from the ground, including the overhangs, and pick the pitch. You get the real roof area, squares, shingle bundles or tiles, and underlayment rolls.

Your project

Measure along the eaves on the ground, then add the overhang at each end.

ft

The other side, eave to eave, with both overhangs.

ft

Inches of rise per 12 in of run. Most houses are 4/12 to 9/12, or 18 to 37 degrees.

Fine tune

10% for simple gable roofs, 15% for hips, valleys and dormers.

%
Prices (optional)Type your local prices to see what it costs.
$
$

You need

1,476sq ft

Roof area with waste

Roof surface
1,342 sq ft
Roofing squares
14.8 squares
Shingle bundles
45 bundles3 per square
Underlayment
2 rolls10 squares each
Slope factor
1.118

Shopping list

  • Shingle bundles45 bundles · 3 per square
  • Synthetic underlayment2 rolls · 10 squares each

Counts are rounded up so you are never short.

Roofing: common sizes at a glance

Worked out with the calculator above, including its default waste allowance. Your own numbers go in the calculator.

ProjectRoof area with wasteWhat to buy
40 × 30 ft1,476 sq ft45 bundles (3 per square) · 2 rolls (10 squares each)
50 × 40 ft2,460 sq ft74 bundles (3 per square) · 3 rolls (10 squares each)
60 × 50 ft3,690 sq ft111 bundles (3 per square) · 4 rolls (10 squares each)
60 × 30 ft2,214 sq ft67 bundles (3 per square) · 3 rolls (10 squares each)

How to measure a roof from the ground

You do not need to climb up. Measure the footprint of the roof from below, length × width including the overhangs, then multiply by the slope factor for the pitch. Every plane with the same pitch grows by the same factor, so this works for gable and hip roofs alike.

PitchAngleSlope factor
3/1214.0°1.031
4/1218.4°1.054
5/1222.6°1.083
6/1226.6°1.118
7/1230.3°1.158
8/1233.7°1.202
9/1236.9°1.250
10/1239.8°1.302
12/1245°1.414

A 40 × 30 ft footprint at 6/12: 1,200 × 1.118 = 1,342 sq ft of roof. With 10% waste that is 1,476 sq ft: 14.8 squares, or 45 bundles of shingles.

Squares, bundles and underlayment

  • Square: 100 sq ft of roof (9.29 m²).
  • Bundles: most 3 tab and architectural shingles come 3 bundles to the square. Some heavy designer shingles need 4 or 5: check the wrapper.
  • Underlayment: a synthetic roll usually covers 10 squares. Felt covers far less: about 4 squares per roll of #15 and 2 of #30.
  • Metric: bitumen shingle packs cover about 3 m², and underlay membranes often come in 1.5 × 50 m rolls (75 m²).

Ridge caps, starter strips and drip edge are bought by length. Measure the ridges, hips and eaves and add them to the list.

Roof tiles

Tile counts depend on the tile size and its overlap. Large interlocking concrete tiles need about 10 per m² (about 90 per square), smaller clay tiles 12 to 15 per m², and plain tiles laid double 30 or more. The data sheet for your tile has the exact figure.

Tile is three to four times heavier than asphalt shingles. Switching a shingle roof to tile needs a check of the roof framing first.

Questions people ask

How many bundles of shingles do I need?

Three per square. A roof of 1,500 sq ft is 15 squares: 45 bundles, or 50 with 10% waste.

What is a roofing square?

100 square feet of roof surface, about 9.3 m². Shingles, underlayment and roofing labor are all priced by the square.

How do I find my roof pitch?

Hold a level flat against a rafter or the roof edge, mark 12 in along it and measure straight up to the roof. That number over 12 is the pitch: 6 in means 6/12.

How much does pitch add to the roof area?

A 4/12 roof is about 5% larger than its footprint, 6/12 about 12%, 9/12 25% and 12/12 41%.

Sources and data

  • International Residential Code 2021, R905.2 (asphalt shingles) and R905.3 (clay and concrete tile)
  • Shingle packaging: 3 bundles per square for standard shingles
  • Synthetic underlayment rolls of 10 squares (1,000 sq ft)

Last reviewed November 16, 2026 · How we calculate

Next steps in your project