Skip to content
Measured Yard

Rebar Calculator

Enter the slab size, the bar spacing and the stock length. You get the bars each way, the total length, the stock bars to buy counting the laps, and the ties.

Your project

ft
ft

Patios and driveways often use #3 or #4 bars at 12 to 18 in. Follow your plans.

Home centers sell 10 and 20 ft bars. Longer bars mean fewer laps.

Fine tune

Keep bars 3 in (7.5 cm) in from the edges of a slab poured on the ground.

in

About 40 bar diameters: 15 in for #3, 20 in for #4, 25 in for #5.

in
Prices (optional)Type your local prices to see what it costs.
$

You need

18bars

Bars to buy · 20 ft

Total bar length
336.5 ft
Bars along the length
9 bars
Bars along the width
14 bars
Ties
126 ties

This lays out a simple grid for a slab on the ground. Footings, suspended slabs and anything structural need the bar size, spacing and laps from your plans or local code.

Shopping list

  • Rebar18 bars · 20 ft
  • Rebar ties126 ties

Counts are rounded up so you are never short.

Rebar: common sizes at a glance

Worked out with the calculator above, including its default waste allowance. Your own numbers go in the calculator.

ProjectBars to buyWhat to buy
10 × 10 ft8 bars8 bars (20 ft) · 64 ties
20 × 12 ft18 bars18 bars (20 ft) · 126 ties
20 × 20 ft28 bars28 bars (20 ft) · 196 ties
24 × 24 ft44 bars44 bars (20 ft) · 289 ties

How to count rebar for a slab

Bars sit on both cover lines and never more than one spacing apart. Bars each way = (side minus 2 × cover) ÷ spacing, rounded up, plus one. Each bar is as long as the other side minus the cover at both ends.

A 20 × 12 ft slab with bars at 18 in and 3 in cover: 9 bars of 19 ft 6 in run the long way and 14 bars of 11 ft 6 in run across. That is 336.5 ft of bar and 126 crossings to tie. Cut from 20 ft stock, it takes 18 bars.

BarDiameterWeightLap at 40 diameters
#33/8 in (9.5 mm)0.376 lb per ft15 in
#41/2 in (12.7 mm)0.668 lb per ft20 in
#55/8 in (15.9 mm)1.043 lb per ft25 in
10 mm10 mm0.62 kg per m40 cm
12 mm12 mm0.89 kg per m48 cm, use 50

Laps, offcuts and ties

  • Laps: where two bars meet, overlap them by the lap length and tie them together. A run longer than one stock bar needs a lap at every joint.
  • Offcuts: the calculator cuts the runs in order from full bars. A leftover piece longer than two laps starts the next run with a lap; shorter scraps are not counted.
  • Ties: one wire tie at every crossing. Many crews tie every crossing at the edges and every other one in the middle, which saves almost half.

Hold the grid up in the middle of the slab on chairs or small concrete blocks every 3 to 4 ft. Rebar lying on the ground does almost nothing.

Questions people ask

How much rebar do I need for a 20 × 20 slab?

At 18 in spacing with 3 in cover, 14 bars of 19 ft 6 in each way: 546 ft, or 28 bars of 20 ft. At 12 in spacing it is 21 bars each way, 819 ft and 42 bars.

What size rebar for a driveway?

#3 or #4 bars (10 or 12 mm) at 12 to 18 in are common in a 4 to 6 in residential slab. Some driveways use wire mesh or fibers instead: follow your plans or local code.

How long should a rebar lap splice be?

A common rule is 40 bar diameters: 20 in for #4 and about 50 cm for 12 mm bars. Structural work uses the lap your engineer specifies.

How many rebar ties do I need?

One per crossing: the bars one way times the bars the other way. A 20 × 12 ft slab at 18 in has 126 crossings.

Sources and data

  • Concrete Reinforcing Steel Institute (CRSI) placing practice for slab bar supports and ties
  • ASTM A615 bar sizes and weights

Last reviewed November 16, 2026 · How we calculate

Next steps in your project